Nanocomposite Permanent Magnets Based on SrFe12O19-Fe3O4 Hard-Soft Ferrites

Journal of Superconductivity and Novel Magnetism - Nanocomposites consisting of strontium ferrite and magnetite are prepared to investigate the effect of exchange coupling between the hard and soft...     

Opportunistic large array concentric routing algorithm (OLACRA) for upstream routing in wireless sensor networks

An opportunistic large array (OLA) is a form of cooperative diversity in which a large group of relays or forwarding nodes operate without any mutual coordination, but naturally fire together in response to energy received from a single source or another OLA. When used for broadcast, OLAs form concentric rings around the source, and have been shown to use less transmit energy than conventional multi-hop protocols during broadcasting. The OLA concentric routing algorithm (OLACRA) and its variants, the main contributions of this paper, leverage the concentric ring structure of the OLAs during the initialization phase to limit the node participation on the upstream connection. For the simulation scenarios considered in this paper, OLACRA is shown to save over 80% of the transmit energy relative to other OLA-based schemes. This paper analyzes the performance of OLACRA over ‘deterministic channels’ or non-faded orthogonal channels and on ‘diversity’ or Rayleigh flat-fading channels with limited orthogonality. Enhancements to OLACRA to further improve its energy efficiency by limited broadcasting in the initial upstream level and limiting the downlink ‘step-sizes’ are also considered. A simple contention avoidance scheme for WSNs with multiple flows is also proposed. In addition to this, the robustness of OLACRA over mobile channels is also studied. The protocols are tested using Monte Carlo evaluation.     

Angstrom Scale Wear of the Air-Bearing Sliders in Hard Disk Drives

We utilize thermal fly-height control (TFC) technology to perform in situ measurements of carbon overcoat wear at the angstrom level at the read–write area of magnetic recording heads. We also study the durability of the molecularly thin lubricated disk surface. Experimental findings reveal a linear relationship between the quantified carbon wear depth on the flying head versus the head–disk contact level produced by the TFC power. It is demonstrated that this method can serve as a measurement and probing technique of wear resistance for different types of lubricants. Lubricants possessing more polar hydroxyl end-groups and less mobility tend to show a superior surface stability under head–disk contacts, but raise concerns on head carbon overcoat wear.     

Using OpenFlow to provide cut-through switching in MobilityFirst

Mobile devices are expected to become the Internet’s predominant technology. Current protocols such as TCP/IP were not originally designed with mobility as a key consideration, and therefore underperform under challenging mobile and wireless conditions. MobilityFirst, a clean slate architecture proposal, embraces several key concepts centered around secure identifiers that inherently support mobility and trustworthiness as key requirements of the network architecture. This includes a hop-by-hop segmented data transport based on a globally unique identifier. This allows late and dynamic rebinding of end-point addresses to support mobility. While this provides critical gains in wireless segments, some overheads are incurred even in stable segments such as in the core. Bypassing routing-layer decisions in these cases, with lower layer cut-through forwarding, can improve said gains. In this work, we introduce a general bypass capability within the MobilityFirst architecture that provides better performance and enables both individual and aggregate flow-level traffic control. Furthermore, we present an OpenFlow-based proof-of-concept implementation of the bypass function using layer 2 VLAN tagging. We run experiments on the ORBIT and Global Environment for Network Innovations (GENI) testbeds to evaluate the performance and scalability of the solution. By implementing the bypass functionality, we are able to significantly reduce the number of messages processed by the controller as well as the number of flow rules that need to be pushed into the switches.     

Constrained Sintering of Low-Temperature Co-Fired Ceramics

This paper discusses the effect of uniaxial compressive stress and pressureless constraint on the microstructure, density, and shrinkage anisotropy during the sintering of two commercial low-temperature co-fired ceramic (LTCC) systems, i.e., Heraeus CT2000 (CT) and DuPont 951Tape (DU). Under uniaxial compression, the ratio of axial to transverse shrinkage of DU is significantly higher than that of CT. A simple linear viscous theory was used to estimate the change in the strain rates produced by the external stress and the stress required to produce zero shrinkage. The theory was found to overestimate the measured stress-induced strain rates. The uniaxial compressive stress required for zero overall shrinkage was estimated to be ∼60 kPa for DU and 80 kPa for CT. The estimate for the DU materials was in good agreement with the experimental data, but there was significant deviation for the CT material. Higher viscosity and higher constraining stresses led to lower densities in pressure-less constrained CT specimens compared with DU.     

Reversible metal-insulator transitions in metallic single-walled carbon nanotubes

We report on reversible metal to insulator transitions in metallic single-walled carbon nanotube devices induced by repeated electron irradiation of a nanotube segment. The transition from a low-resistive, metallic state to a high-resistive, insulating state by 3 orders of magnitude was monitored by electron transport measurements. Application of a large voltage bias leads to a transition back to the original metallic state. Both states are stable in time, and transitions are fully reversible and reproducible. The data is evidence for a local perturbation of the nanotube electronic system by removable trapped charges in the underneath substrate and excludes structural damage of the nanotube. The result has implications for using electron-beam lithography in nanotube device fabrication.     

An Enhanced Inter-carrier Interference Reduction Scheme for OFDM System with Phase Noise

Inter-carrier interference (ICI) reduction techniques achieve a better carrier-to-interference ratio (CIR) in OFDM system in the presence of synchronisation errors. However, the frequency diversity available on the frequency-selective channel has not been utilised by conventional ICI reduction techniques. In this paper, the frequency diversity of ICI reduction methods in the presence of phase noise over frequency-selective fading channels is analysed. Based on the analysis, an ICI reduction technique is proposed, enhanced symmetric data-conjugate (ESDC) technique, to enhance the frequency diversity in multipath fading channel. The carrier-to-interference ratio (CIR) and common phase error (CPE) of the proposed ICI reduction scheme are derived and the BER performance of the proposed system is compared with the conventional ICI reduction methods such as adjacent data-conjugate (ADC) and symmetric data-conjugate (SDC) methods. Simulation results reveal that the proposed ICI reduction scheme provides an improvement in BER performance over a fading channel and it is also better than conventional ICI reduction techniques in the presence of ICI due to phase noise.